Bench Favorites

Binding wire holds parts and assemblies in position on the bench while you solder, so a joint stays aligned through heating and quenching. This wir...

Finish a chain end cleanly at the bench with a cap that sits flush and hides the raw termination.These sterling silver flat chain end caps give nec...

A rawhide mallet moves and seats metal without leaving a mark on the surface, which is why it stays within reach on a forming bench. These tough, l...

Jay Whaley has done it again. These precision bezel cutting shears have been specially modified to deliver perfect 90-degree cuts on bezel material...

A friction ear nut pushes onto an earring post and holds the earring on the ear with spring tension, and this is the standard 5.8mm size measured a...

Zinc-free eutectic silver solder is the piece you reach for when a joint has to survive an enameling firing without spoiling the enamel. Commonly k...

Ram roller burnishers hammer porosity, scratches, and fire scale out of precious metal castings, compressing the surface so it finishes denser and ...

Thin, flexible sterling silver serrated bezel strip wire designed for creating bezel settings. The serrated edge grips and holds stones securely wh...

Deep channel wire wraps around a faceted stone to hold it without prongs, and this profile is drawn in sterling silver by Harmony. The wire is draw...

These 3/32" shank mandrels are designed for use with Moore's Snap-On Discs and other brands of sanding discs that accept brass center holes. Constr...

These high speed steel twist drills are permanently mounted on uniform 3/32" shanks for use in quick-change collet style handpieces, giving you con...

Polishing right up against a set stone calls for an abrasive gentle enough to work the bezel without touching the stone. Ottotech by Eve Fine Pumic...

Pack of 3 burnishing pins designed specifically for use with Peter Keep's Ezi-Set Stone Setting Pliers (part #146.015). This new and improved versi...

Thermo-Loc holds rings, bracelets, pendants and other irregular or fragile pieces steady at the bench when a clamp or a vise cannot take a safe gri...

Garnet belongs to a group of closely related minerals sharing the same crystal structure but varying chemical compositions. While garnet occurs in ...

Honeycomb soldering boards give the bench a stable, heat-reflecting surface for soldering, in 1/2" thick perforated panels that send heat back towa...

A V-point graver cuts the V-shaped lines used for bright-cutting, undercutting bezels, and setting stones. For years, engravers and jewelers have s...

Ottotech by Eve medium pumice wheels offer a slightly more aggressive cut than fine-grit pumice, making them ideal for polishing bezels and prongs ...

Setting burs cut the seat that holds a stone in place. Swiss Fig. Q Setting Burs are precision-crafted from tungsten vanadium steel and manufacture...

The Wolf Precision Tungsten Scribe delivers clean, accurate lines on a wide range of metals and soft materials. Its tip is made from tungsten carbi...

A quick change tool holder is the part that grips the graver and drops into the handle or handpiece, so a shank can be swapped without re-seating t...

Glardon-Vallorbe LF0502-M ceramic fiber files in a pillar (thin flat stick) shape provide precise finishing and polishing access in hard-to-reach a...

Lay out stone spacing, mark borders, and transfer measurements at the bench with a divider rigid enough to hold its setting through detailed work. ...

Epoxy 330 is the best-selling two-part epoxy at Otto Frei — and for good reason. This fast-drying, water-clear adhesive is trusted by jewelers for ...

Bring a contoured surface up to a bright, even finish at the bench, wet or dry, without the uneven scratch pattern a coarse-graded paper leaves beh...

A rolling mill flattens and reduces metal at the bench, and this one takes material up to 4mm thick across 80mm flat rollers. The Durston 1002 Hobb...

The Bench Pin with V-Slot & Clamp is an essential bench tool for jewelers and metalsmiths, providing a stable working surface for filing, sawin...

These Italian-made 3 mm diameter silicone polishing rods feature a pre-formed pointed tip, eliminating the need to shape them before use. Designed ...

Borax casting flux powder controls oxidation while you melt and pour at the bench, keeping metal cleaner for better fills and fewer inclusions. Use...

These synthetic red sable flux brushes feature hand-cupped tips shaped to needle-sharp points, allowing them to hold a generous amount of flux or c...

Blue Max fine muslin buffs are specially treated to hold polishing compounds longer and deliver extended service life compared to untreated buffs. ...

Swiss made jewelers thread taps designed for use with the Colibri Screwplate and individual Swiss jewelers dies. These taps feature a coarser threa...